640-605 Remote Access 2.0 考试大纲

　★Exam Description
　　 The Remote Access exam (RMTAC 640-605) is one exam within two different
series of exams required to achieve either CCNP or CCDP Routing and Switching
　　★Exam Topics
　　 The following topics are general guidelines for the content likely to be
included on the Remote Access exam. However, other related topics may also appear
　　■.Cisco Remote Access Networks Introduction

　　 * Specify and /or identify the Cisco products that best meet the WAN
connection requirements for permanent or dialup access connections
　　■.Selecting CISCO Products for Remote Connections
　　 * Explain and/or identify the advantages and disadvantages of WAN connection
　　 * Select the appropriate WAN connection types that address specific site
　　 * Select Cisco equipment that will suit the specific needs of a WAN topology
　　■.Assembling and Cabling the WAN Components

　　 * Identify the components and connections necessary to allow WAN connections
like Frame Relay, and ISDN PRI from the central site to a branch office.
　　 * Identify the components and connections necessary to allow WAN connections
like Frame Relay, and ISDN BRI from a branch office to the central site
　　 * Identify the components and connections necessary to allow a WAN
connections like ISDN BRI from a telecommuter site to the central site
　　■.Configuring Asynchronous Connections to a Central Site with Modems
　　 * Specify the commands and procedures necessary to configure an access
server for modem connectivity so telecommuters can access the central site.
　　 * Specify the commands and procedures to configure the central site for dial
　　 * Specify the commands used to reverse Telnet to the modem and configure the
　　 * Specify the commands and procedures used to set up the modem
　　■.Configuring PPP and Controlling Network Access with PAP and CHAP
　　 * Specify the commands and syntax used to configure a PPP connection between
　　 * Specify the commands and syntax to configure PAP or CHAP authentication to
　　 * Configure Multilink PPP to increase the data throughput.
　　 * Specify the commands used to verify proper PPP configuration and
　　 * Accessing the Central Site with Windows 95
　　 * Specify the commands and procedures to configure a PC to complete a dialup
call to the central site router through the traditional telephone network.
　　■.Using ISDN and DDR Technologies to Enhance Remote Connectivity
　　 * Identify when to use ISDN BRI and PRI services and select the service that
best suits a set of given requirements.
　　 * Identify the Q.921 and Q.931 signaling and call setup sequences.
　　 * Specify the commands used to configure ISDN BRI and PRI
　　 * Specify the commands used to configure DDR
　　■.Optimizing the use of DDR Interfaces
　　 * Specify or select appropriate dialup capabilities to place a call.
　　 * Specify the commands and procedures to configure rotary groups and dialer
　　 * Specify the commands used to verify proper dialer profile or rotary group
configuration and troubleshoot an incorrect configuration.
　　■.Using X.25 for Remote Access
　　 * Specify the commands and procedures to configure an X.25 WAN connection
　　 * Specify proper X.121 addresses and the commands used to assign them to
　　 * Specify the commands and procedures used to verify proper X.25
configuration and troubleshoot incorrect X.25 configuration
　　■.Establishing a Dedicated Frame Relay Connection and Control Traffic Flow
　　 * Specify the commands and procedures used to configure a Frame Relay WAN
connection between the central office and branch office
　　 * Specify the commands to configure subinterfaces on virtual interfaces to
　　 * Specify the commands used to configure Frame Relay traffic shaping.
　　 * Specify the commands and procedures used to verify proper Frame Relay
configuration and troubleshoot an incorrect configuration
　　■.Enabling a Backup to the Permanent Connection
　　 * Specify the procedure and commands used to configure a backup connection
　　 * Specify the procedure and commands used to configure a backup connection
to activate when the primary line reaches a specified threshold.
　　 * Specify the procedure and commands used to configure a dialer to function
　　■.Managing Network Performance with Queuing and Compression
　　 * Determine why queuing is enabled, identify alternative queuing protocols
that Cisco products support, and determine the best queuing method to implement.
　　 * Specify the commands to configure weighted-fair, priority and custom
　　 * Specify the commands and procedures used to verify proper queuing
configuration and troubleshoot incorrect configuration
　　 * Specify the commands and procedures used to effectively select and
　　■.Scaling IP Addresses with Network Address Translation
　　 * Describe how NAT and PAT operate.
　　 * Specify the commands and procedures to configure NAT and PAT to allow
reuse of registered IP addresses in a private network.
　　 * Verify proper configuration of NAT and PAT with available Cisco
　　■.Using AAA to Scale Access Control in an Expanding Network
　　 * Specify, recognize or describe the security features of CiscoSecure and
　　 * Specify the commands and procedures used to configure a router to access a
　　 * Specify the commands used to configure AAA on a router to control access